Hardwood Sizes, Species & Profiles — Interactive 3D Guide
Every hardwood species, board size and milling profile we stock, as interactive 3D models you can rotate and zoom — plus a side-by-side comparison tool that shows any two boards at true relative scale. Use this guide to see how species, thicknesses, widths, and edge profiles differ before choosing a product.
Nominal vs. Actual, in Brief
Hardwood lumber is sold by nominal size (1x6, 5/4x6) while the actual milled dimensions are smaller — a 1x6 measures about 3/4″ thick by 5-1/2″ wide after surfacing, in every species. Every board below lists its true actual dimensions, and each 3D model is built from those exact measurements.
Each board below also lists its approximate face coverage — the width that actually shows once the board is installed. Square-edge and pregrooved boards expose their full width, but interlocking and overlapping profiles lose part of the width inside the joint (a 1x6 tongue & groove board is 5-1/2″ wide and covers about 5-1/8″). Use coverage, not actual width, when figuring square footage.
Face coverage figures are approximate. Actual coverage varies with milling tolerances, the mill run and profile tooling used, moisture content and seasonal movement, the fastening hardware and gap spacing you install with, and how tightly boards are drawn together. Always confirm coverage against the boards in hand and add waste allowance before ordering.
Beyond size and species, every board is milled to a profile that determines how it installs and how the finished surface looks. Standard decking is eased-edge (E4E) — flat faces with slightly rounded long edges for face-screwed installs. Pregrooved boards carry a slot on each side edge for hidden deck fasteners, keeping the surface free of screws. Tongue & groove boards interlock for porches, soffits, and ceilings, while siding profiles like shiplap and rainscreen overlap to shed water.
Each entry below states the profile and edge treatment, and the interactive model shows the true milled cross-section — spin the board end-on to see exactly how grooves, tongues, and laps are cut.
How to Use the Interactive 3D Models
Click Load interactive 3D model on any board below (models load only when you ask, so the page stays fast). Drag to rotate, and scroll or pinch to zoom. Rotating a board end-on is the clearest way to compare profiles — for example, the center fastener groove on a pregrooved board versus the offset tongue on tongue & groove. Every dimension shown in the model is also written out in plain text, so you never need the 3D view to get the specifications.
Compare Species, Sizes & Profiles Side by Side
Pick any two boards — same species or different — and compare them at true relative scale, with hardness, density, color and rot-resistance differences summarized below. Face coverage figures are approximate and vary with milling tolerance, moisture, hardware and gap spacing. Use the End / Profile view to see how edge treatments like pregrooved and tongue & groove differ. You can also tap Compare on any board card below; with two boards already selected, the next pick replaces Board B.
Loads both models on demand at the same scale — drag to rotate, scroll or pinch to zoom. All dimensions are also shown in plain text below.
Board A
1x6 Ipe Decking
3D model loads with the button above
Board A
1x6 Ipe Decking
Species
Ipe
Janka hardness
3680
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Eased-Edge
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Every species, size and milled profile we stock. Filter by species, board size or profile, then load any model to rotate it and inspect the milled cross-section.
Species
Size
Profile
Showing 415 of 415 boards
Loads on demand — drag to rotate, scroll or pinch to zoom
1x1 Ipe Decking
Species
Ipe
Nominal size
1x1
Actual dimensions
3/4" × 3/4"
Face coverage (approx.)
3/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x2 Ipe Decking
Species
Ipe
Nominal size
1x2
Actual dimensions
3/4" × 1 1/2"
Face coverage (approx.)
1 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x2 Ipe Shiplap Siding
Species
Ipe
Nominal size
1x2
Actual dimensions
3/4" × 1 1/2"
Face coverage (approx.)
1"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x2 Ipe Tongue & Groove Soffit
Species
Ipe
Nominal size
1x2
Actual dimensions
3/4" × 1 1/2"
Face coverage (approx.)
1 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x2 Ipe Railing
Species
Ipe
Nominal size
2x2
Actual dimensions
1 1/2" × 1 1/2"
Face coverage (approx.)
1 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Ipe Decking
Species
Ipe
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Ipe Pre-Grooved Decking
Species
Ipe
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Ipe Shiplap Soffit
Species
Ipe
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Ipe Tongue & Groove Soffit
Species
Ipe
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x3 Ipe Decking
Species
Ipe
Nominal size
2x3
Actual dimensions
1 1/2" × 2 1/2"
Face coverage (approx.)
2 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Ipe Bevel Siding
Species
Ipe
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Ipe Channel Siding
Species
Ipe
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
2 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Ipe Decking
Species
Ipe
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Ipe Nickel Gap Siding
Species
Ipe
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Ipe Pre-Grooved Decking
Species
Ipe
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Ipe Shiplap Siding
Species
Ipe
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Ipe Tongue & Groove Outdoor Flooring
Species
Ipe
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Ipe V-Groove Siding
Species
Ipe
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Ipe Bevel Siding
Species
Ipe
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Ipe Channel Siding
Species
Ipe
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
2 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Ipe Decking
Species
Ipe
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Ipe Nickel Gap Siding
Species
Ipe
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Ipe Pre-Grooved Decking
Species
Ipe
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Ipe Rainscreen Soffit
Species
Ipe
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
2 1/2"
Profile
Rainscreen
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
An overlapping lap joint engineered to shed water behind ventilated cladding systems.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Ipe Shiplap Soffit
Species
Ipe
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Ipe Tongue & Groove Soffit
Species
Ipe
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Ipe V-Groove Siding
Species
Ipe
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x4 Ipe Decking
Species
Ipe
Nominal size
2x4
Actual dimensions
1 1/2" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x4 Ipe Pre-Grooved Decking
Species
Ipe
Nominal size
2x4
Actual dimensions
1 1/2" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x4 Ipe Tongue & Groove Outdoor Flooring
Species
Ipe
Nominal size
2x4
Actual dimensions
1 1/2" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
3x4 Ipe Timbers
Species
Ipe
Nominal size
3x4
Actual dimensions
2 1/2" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
4x4 Ipe Fencing
Species
Ipe
Nominal size
4x4
Actual dimensions
3 1/2" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Ipe Bevel Siding
Species
Ipe
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Ipe Channel Siding
Species
Ipe
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Ipe Decking
Species
Ipe
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Ipe Nickel Gap Siding
Species
Ipe
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Ipe Pre-Grooved Decking
Species
Ipe
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Ipe Rainscreen Siding
Species
Ipe
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Rainscreen
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
An overlapping lap joint engineered to shed water behind ventilated cladding systems.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Ipe Shiplap Siding
Species
Ipe
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Ipe Tongue & Groove Decking
Species
Ipe
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Ipe V-Groove Siding
Species
Ipe
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Ipe Bevel Siding
Species
Ipe
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Ipe Channel Siding
Species
Ipe
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Ipe Decking
Species
Ipe
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Ipe Nickel Gap Siding
Species
Ipe
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Ipe Pre-Grooved Decking
Species
Ipe
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Ipe Rainscreen Siding
Species
Ipe
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Rainscreen
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
An overlapping lap joint engineered to shed water behind ventilated cladding systems.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Ipe Shiplap Siding
Species
Ipe
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Ipe Tongue & Groove Decking
Species
Ipe
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Ipe V-Groove Siding
Species
Ipe
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x6 Ipe Decking
Species
Ipe
Nominal size
2x6
Actual dimensions
1 1/2" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x6 Ipe Pre-Grooved Decking
Species
Ipe
Nominal size
2x6
Actual dimensions
1 1/2" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x6 Ipe Tongue & Groove Outdoor Flooring
Species
Ipe
Nominal size
2x6
Actual dimensions
1 1/2" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
3x6 Ipe Timbers
Species
Ipe
Nominal size
3x6
Actual dimensions
2 1/2" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
4x6 Ipe Timbers
Species
Ipe
Nominal size
4x6
Actual dimensions
3 1/2" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
6x6 Ipe Fencing
Species
Ipe
Nominal size
6x6
Actual dimensions
5 1/2" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x8 Ipe Bevel Siding
Species
Ipe
Nominal size
1x8
Actual dimensions
3/4" × 7 1/4"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x8 Ipe Channel Siding
Species
Ipe
Nominal size
1x8
Actual dimensions
3/4" × 7 1/4"
Face coverage (approx.)
6 1/4"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x8 Ipe Siding
Species
Ipe
Nominal size
1x8
Actual dimensions
3/4" × 7 1/4"
Face coverage (approx.)
7 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x8 Ipe Nickel Gap Siding
Species
Ipe
Nominal size
1x8
Actual dimensions
3/4" × 7 1/4"
Face coverage (approx.)
6 3/4"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x8 Ipe Shiplap Siding
Species
Ipe
Nominal size
1x8
Actual dimensions
3/4" × 7 1/4"
Face coverage (approx.)
6 3/4"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x8 Ipe Tongue & Groove Siding
Species
Ipe
Nominal size
1x8
Actual dimensions
3/4" × 7 1/4"
Face coverage (approx.)
6 7/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x8 Ipe V-Groove Siding
Species
Ipe
Nominal size
1x8
Actual dimensions
3/4" × 7 1/4"
Face coverage (approx.)
6 7/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x8 Ipe Bevel Siding
Species
Ipe
Nominal size
5/4x8
Actual dimensions
1" × 7 1/4"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x8 Ipe Channel Siding
Species
Ipe
Nominal size
5/4x8
Actual dimensions
1" × 7 1/4"
Face coverage (approx.)
6 1/4"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x8 Ipe Decking
Species
Ipe
Nominal size
5/4x8
Actual dimensions
1" × 7 1/4"
Face coverage (approx.)
7 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x8 Ipe Nickel Gap Siding
Species
Ipe
Nominal size
5/4x8
Actual dimensions
1" × 7 1/4"
Face coverage (approx.)
6 3/4"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x8 Ipe V-Groove Siding
Species
Ipe
Nominal size
5/4x8
Actual dimensions
1" × 7 1/4"
Face coverage (approx.)
6 7/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x8 Ipe Timbers
Species
Ipe
Nominal size
2x8
Actual dimensions
1 1/2" × 7 1/4"
Face coverage (approx.)
7 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x8 Ipe Shiplap Siding
Species
Ipe
Nominal size
2x8
Actual dimensions
1 1/2" × 7 1/4"
Face coverage (approx.)
6 3/4"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x8 Ipe Tongue & Groove Siding
Species
Ipe
Nominal size
2x8
Actual dimensions
1 1/2" × 7 1/4"
Face coverage (approx.)
6 7/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
3x8 Ipe Timbers
Species
Ipe
Nominal size
3x8
Actual dimensions
2 1/2" × 7 1/4"
Face coverage (approx.)
7 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
4x8 Ipe Timbers
Species
Ipe
Nominal size
4x8
Actual dimensions
3 1/2" × 7 1/4"
Face coverage (approx.)
7 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
6x8 Ipe Timbers
Species
Ipe
Nominal size
6x8
Actual dimensions
5 1/2" × 7 1/4"
Face coverage (approx.)
7 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
8x8 Ipe Timbers
Species
Ipe
Nominal size
8x8
Actual dimensions
7 1/4" × 7 1/4"
Face coverage (approx.)
7 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x10 Ipe Shiplap Siding
Species
Ipe
Nominal size
1x10
Actual dimensions
3/4" × 9 1/4"
Face coverage (approx.)
8 3/4"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x10 Ipe Tongue & Groove Siding
Species
Ipe
Nominal size
1x10
Actual dimensions
3/4" × 9 1/4"
Face coverage (approx.)
8 7/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x10 Ipe Timbers
Species
Ipe
Nominal size
2x10
Actual dimensions
1 1/2" × 9 1/4"
Face coverage (approx.)
9 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
3x10 Ipe Timbers
Species
Ipe
Nominal size
3x10
Actual dimensions
2 1/2" × 9 1/4"
Face coverage (approx.)
9 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
4x10 Ipe Timbers
Species
Ipe
Nominal size
4x10
Actual dimensions
3 1/2" × 9 1/4"
Face coverage (approx.)
9 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
6x10 Ipe Timbers
Species
Ipe
Nominal size
6x10
Actual dimensions
5 1/2" × 9 1/4"
Face coverage (approx.)
9 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x12 Ipe Timbers
Species
Ipe
Nominal size
2x12
Actual dimensions
1 1/2" × 11 1/4"
Face coverage (approx.)
11 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
3x12 Ipe Timbers
Species
Ipe
Nominal size
3x12
Actual dimensions
2 1/2" × 11 1/4"
Face coverage (approx.)
11 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
4x12 Ipe Timbers
Species
Ipe
Nominal size
4x12
Actual dimensions
3 1/2" × 11 1/4"
Face coverage (approx.)
11 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
6x12 Ipe Timbers
Species
Ipe
Nominal size
6x12
Actual dimensions
5 1/2" × 11 1/4"
Face coverage (approx.)
11 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x1 Cumaru Decking
Species
Cumaru
Nominal size
1x1
Actual dimensions
3/4" × 3/4"
Face coverage (approx.)
3/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x2 Cumaru Decking
Species
Cumaru
Nominal size
1x2
Actual dimensions
3/4" × 1 1/2"
Face coverage (approx.)
1 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x2 Cumaru Shiplap Siding
Species
Cumaru
Nominal size
1x2
Actual dimensions
3/4" × 1 1/2"
Face coverage (approx.)
1"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x2 Cumaru Tongue & Groove Soffit
Species
Cumaru
Nominal size
1x2
Actual dimensions
3/4" × 1 1/2"
Face coverage (approx.)
1 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x2 Cumaru Railing
Species
Cumaru
Nominal size
2x2
Actual dimensions
1 1/2" × 1 1/2"
Face coverage (approx.)
1 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Cumaru Decking
Species
Cumaru
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Cumaru Pre-Grooved Decking
Species
Cumaru
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Cumaru Shiplap Soffit
Species
Cumaru
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Cumaru Tongue & Groove Soffit
Species
Cumaru
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x3 Cumaru Decking
Species
Cumaru
Nominal size
2x3
Actual dimensions
1 1/2" × 2 1/2"
Face coverage (approx.)
2 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Cumaru Bevel Siding
Species
Cumaru
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Cumaru Channel Siding
Species
Cumaru
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
2 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Cumaru Decking
Species
Cumaru
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Cumaru Nickel Gap Siding
Species
Cumaru
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Cumaru Pre-Grooved Decking
Species
Cumaru
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Cumaru Shiplap Siding
Species
Cumaru
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Cumaru Tongue & Groove Outdoor Flooring
Species
Cumaru
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Cumaru V-Groove Siding
Species
Cumaru
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Cumaru Bevel Siding
Species
Cumaru
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Cumaru Channel Siding
Species
Cumaru
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
2 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Cumaru Decking
Species
Cumaru
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Cumaru Nickel Gap Siding
Species
Cumaru
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Cumaru Pre-Grooved Decking
Species
Cumaru
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Cumaru Rainscreen Soffit
Species
Cumaru
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
2 1/2"
Profile
Rainscreen
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
An overlapping lap joint engineered to shed water behind ventilated cladding systems.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Cumaru Shiplap Soffit
Species
Cumaru
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Cumaru Tongue & Groove Soffit
Species
Cumaru
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Cumaru V-Groove Siding
Species
Cumaru
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x4 Cumaru Decking
Species
Cumaru
Nominal size
2x4
Actual dimensions
1 1/2" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x4 Cumaru Pre-Grooved Decking
Species
Cumaru
Nominal size
2x4
Actual dimensions
1 1/2" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x4 Cumaru Tongue & Groove Outdoor Flooring
Species
Cumaru
Nominal size
2x4
Actual dimensions
1 1/2" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
4x4 Cumaru Fencing
Species
Cumaru
Nominal size
4x4
Actual dimensions
3 1/2" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Cumaru Bevel Siding
Species
Cumaru
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Cumaru Channel Siding
Species
Cumaru
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Cumaru Decking
Species
Cumaru
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Cumaru Nickel Gap Siding
Species
Cumaru
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Cumaru Pre-Grooved Decking
Species
Cumaru
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Cumaru Rainscreen Siding
Species
Cumaru
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Rainscreen
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
An overlapping lap joint engineered to shed water behind ventilated cladding systems.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Cumaru Shiplap Siding
Species
Cumaru
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Cumaru Tongue & Groove Decking
Species
Cumaru
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Cumaru V-Groove Siding
Species
Cumaru
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Cumaru Bevel Siding
Species
Cumaru
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Cumaru Channel Siding
Species
Cumaru
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Cumaru Decking
Species
Cumaru
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Cumaru Nickel Gap Siding
Species
Cumaru
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Cumaru Pre-Grooved Decking
Species
Cumaru
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Cumaru Rainscreen Siding
Species
Cumaru
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Rainscreen
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
An overlapping lap joint engineered to shed water behind ventilated cladding systems.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Cumaru Shiplap Siding
Species
Cumaru
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Cumaru Tongue & Groove Decking
Species
Cumaru
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Cumaru V-Groove Siding
Species
Cumaru
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x6 Cumaru Decking
Species
Cumaru
Nominal size
2x6
Actual dimensions
1 1/2" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x6 Cumaru Pre-Grooved Decking
Species
Cumaru
Nominal size
2x6
Actual dimensions
1 1/2" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x6 Cumaru Tongue & Groove Outdoor Flooring
Species
Cumaru
Nominal size
2x6
Actual dimensions
1 1/2" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x8 Cumaru Siding
Species
Cumaru
Nominal size
1x8
Actual dimensions
3/4" × 7 1/4"
Face coverage (approx.)
7 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x8 Cumaru Siding
Species
Cumaru
Nominal size
5/4x8
Actual dimensions
1" × 7 1/4"
Face coverage (approx.)
7 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x8 Cumaru Timbers
Species
Cumaru
Nominal size
2x8
Actual dimensions
1 1/2" × 7 1/4"
Face coverage (approx.)
7 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x1 Garapa Decking
Species
Garapa
Nominal size
1x1
Actual dimensions
3/4" × 3/4"
Face coverage (approx.)
3/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x2 Garapa Decking
Species
Garapa
Nominal size
1x2
Actual dimensions
3/4" × 1 1/2"
Face coverage (approx.)
1 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x2 Garapa Shiplap Siding
Species
Garapa
Nominal size
1x2
Actual dimensions
3/4" × 1 1/2"
Face coverage (approx.)
1"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x2 Garapa Tongue & Groove Soffit
Species
Garapa
Nominal size
1x2
Actual dimensions
3/4" × 1 1/2"
Face coverage (approx.)
1 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x2 Garapa Railing
Species
Garapa
Nominal size
2x2
Actual dimensions
1 1/2" × 1 1/2"
Face coverage (approx.)
1 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Garapa Decking
Species
Garapa
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Garapa Pre-Grooved Decking
Species
Garapa
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Garapa Shiplap Soffit
Species
Garapa
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Garapa Tongue & Groove Soffit
Species
Garapa
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x3 Garapa Decking
Species
Garapa
Nominal size
2x3
Actual dimensions
1 1/2" × 2 1/2"
Face coverage (approx.)
2 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Garapa Bevel Siding
Species
Garapa
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Garapa Channel Siding
Species
Garapa
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
2 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Garapa Decking
Species
Garapa
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Garapa Nickel Gap Siding
Species
Garapa
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Garapa Pre-Grooved Decking
Species
Garapa
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Garapa Shiplap Siding
Species
Garapa
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Garapa Tongue & Groove Outdoor Flooring
Species
Garapa
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Garapa V-Groove Siding
Species
Garapa
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Garapa Bevel Siding
Species
Garapa
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Garapa Channel Siding
Species
Garapa
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
2 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Garapa Decking
Species
Garapa
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Garapa Nickel Gap Siding
Species
Garapa
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Garapa Pre-Grooved Decking
Species
Garapa
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Garapa Rainscreen Soffit
Species
Garapa
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
2 1/2"
Profile
Rainscreen
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
An overlapping lap joint engineered to shed water behind ventilated cladding systems.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Garapa Shiplap Soffit
Species
Garapa
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Garapa Tongue & Groove Soffit
Species
Garapa
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Garapa V-Groove Siding
Species
Garapa
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x4 Garapa Decking
Species
Garapa
Nominal size
2x4
Actual dimensions
1 1/2" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x4 Garapa Pre-Grooved Decking
Species
Garapa
Nominal size
2x4
Actual dimensions
1 1/2" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x4 Garapa Tongue & Groove Outdoor Flooring
Species
Garapa
Nominal size
2x4
Actual dimensions
1 1/2" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
4x4 Garapa Fencing
Species
Garapa
Nominal size
4x4
Actual dimensions
3 1/2" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Garapa Bevel Siding
Species
Garapa
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Garapa Channel Siding
Species
Garapa
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Garapa Decking
Species
Garapa
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Garapa Nickel Gap Siding
Species
Garapa
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Garapa Pre-Grooved Decking
Species
Garapa
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Garapa Rainscreen Siding
Species
Garapa
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Rainscreen
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
An overlapping lap joint engineered to shed water behind ventilated cladding systems.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Garapa Shiplap Siding
Species
Garapa
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Garapa Tongue & Groove Decking
Species
Garapa
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Garapa V-Groove Siding
Species
Garapa
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Garapa Bevel Siding
Species
Garapa
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Garapa Channel Siding
Species
Garapa
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Garapa Decking
Species
Garapa
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Garapa Nickel Gap Siding
Species
Garapa
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Garapa Pre-Grooved Decking
Species
Garapa
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Garapa Rainscreen Siding
Species
Garapa
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Rainscreen
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
An overlapping lap joint engineered to shed water behind ventilated cladding systems.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Garapa Shiplap Siding
Species
Garapa
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Garapa Tongue & Groove Decking
Species
Garapa
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Garapa V-Groove Siding
Species
Garapa
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x6 Garapa Decking
Species
Garapa
Nominal size
2x6
Actual dimensions
1 1/2" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x6 Garapa Pre-Grooved Decking
Species
Garapa
Nominal size
2x6
Actual dimensions
1 1/2" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x6 Garapa Tongue & Groove Outdoor Flooring
Species
Garapa
Nominal size
2x6
Actual dimensions
1 1/2" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x8 Garapa Siding
Species
Garapa
Nominal size
1x8
Actual dimensions
3/4" × 7 1/4"
Face coverage (approx.)
7 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x8 Garapa Siding
Species
Garapa
Nominal size
5/4x8
Actual dimensions
1" × 7 1/4"
Face coverage (approx.)
7 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x8 Garapa Timbers
Species
Garapa
Nominal size
2x8
Actual dimensions
1 1/2" × 7 1/4"
Face coverage (approx.)
7 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x1 Jatoba Decking
Species
Jatoba
Nominal size
1x1
Actual dimensions
3/4" × 3/4"
Face coverage (approx.)
3/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x2 Jatoba Decking
Species
Jatoba
Nominal size
1x2
Actual dimensions
3/4" × 1 1/2"
Face coverage (approx.)
1 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x2 Jatoba Shiplap Siding
Species
Jatoba
Nominal size
1x2
Actual dimensions
3/4" × 1 1/2"
Face coverage (approx.)
1"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x2 Jatoba Tongue & Groove Siding
Species
Jatoba
Nominal size
1x2
Actual dimensions
3/4" × 1 1/2"
Face coverage (approx.)
1 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x2 Jatoba Railing
Species
Jatoba
Nominal size
2x2
Actual dimensions
1 1/2" × 1 1/2"
Face coverage (approx.)
1 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Jatoba Decking
Species
Jatoba
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Jatoba Pre-Grooved Decking
Species
Jatoba
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Jatoba Shiplap Soffit
Species
Jatoba
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Jatoba Tongue & Groove Soffit
Species
Jatoba
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x3 Jatoba Decking
Species
Jatoba
Nominal size
2x3
Actual dimensions
1 1/2" × 2 1/2"
Face coverage (approx.)
2 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Jatoba Bevel Siding
Species
Jatoba
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Jatoba Channel Siding
Species
Jatoba
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
2 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Jatoba Decking
Species
Jatoba
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Jatoba Nickel Gap Siding
Species
Jatoba
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Jatoba Pre-Grooved Decking
Species
Jatoba
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Jatoba Shiplap Siding
Species
Jatoba
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Jatoba Tongue & Groove Outdoor Flooring
Species
Jatoba
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Jatoba V-Groove Siding
Species
Jatoba
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Jatoba Bevel Siding
Species
Jatoba
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Jatoba Channel Siding
Species
Jatoba
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
2 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Jatoba Decking
Species
Jatoba
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Jatoba Nickel Gap Siding
Species
Jatoba
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Jatoba Pre-Grooved Decking
Species
Jatoba
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Jatoba Rainscreen Soffit
Species
Jatoba
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
2 1/2"
Profile
Rainscreen
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
An overlapping lap joint engineered to shed water behind ventilated cladding systems.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Jatoba Shiplap Soffit
Species
Jatoba
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Jatoba Tongue & Groove Soffit
Species
Jatoba
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Jatoba V-Groove Siding
Species
Jatoba
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x4 Jatoba Decking
Species
Jatoba
Nominal size
2x4
Actual dimensions
1 1/2" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x4 Jatoba Pre-Grooved Decking
Species
Jatoba
Nominal size
2x4
Actual dimensions
1 1/2" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x4 Jatoba Tongue & Groove Outdoor Flooring
Species
Jatoba
Nominal size
2x4
Actual dimensions
1 1/2" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
4x4 Jatoba Fencing
Species
Jatoba
Nominal size
4x4
Actual dimensions
3 1/2" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Jatoba Bevel Siding
Species
Jatoba
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Jatoba Channel Siding
Species
Jatoba
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Jatoba Decking
Species
Jatoba
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Jatoba Nickel Gap Siding
Species
Jatoba
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Jatoba Pre-Grooved Decking
Species
Jatoba
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Jatoba Rainscreen Siding
Species
Jatoba
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Rainscreen
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
An overlapping lap joint engineered to shed water behind ventilated cladding systems.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Jatoba Shiplap Siding
Species
Jatoba
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Jatoba Tongue & Groove Decking
Species
Jatoba
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Jatoba V-Groove Siding
Species
Jatoba
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Jatoba Bevel Siding
Species
Jatoba
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Jatoba Channel Siding
Species
Jatoba
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Jatoba Decking
Species
Jatoba
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Jatoba Nickel Gap Siding
Species
Jatoba
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Jatoba Pre-Grooved Decking
Species
Jatoba
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Jatoba Rainscreen Siding
Species
Jatoba
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Rainscreen
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
An overlapping lap joint engineered to shed water behind ventilated cladding systems.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Jatoba Shiplap Siding
Species
Jatoba
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Jatoba Tongue & Groove Decking
Species
Jatoba
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Jatoba V-Groove Siding
Species
Jatoba
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x6 Jatoba Decking
Species
Jatoba
Nominal size
2x6
Actual dimensions
1 1/2" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x6 Jatoba Pre-Grooved Decking
Species
Jatoba
Nominal size
2x6
Actual dimensions
1 1/2" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x6 Jatoba Tongue & Groove Outdoor Flooring
Species
Jatoba
Nominal size
2x6
Actual dimensions
1 1/2" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x8 Jatoba Siding
Species
Jatoba
Nominal size
1x8
Actual dimensions
3/4" × 7 1/4"
Face coverage (approx.)
7 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x8 Jatoba Siding
Species
Jatoba
Nominal size
5/4x8
Actual dimensions
1" × 7 1/4"
Face coverage (approx.)
7 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x8 Jatoba Timbers
Species
Jatoba
Nominal size
2x8
Actual dimensions
1 1/2" × 7 1/4"
Face coverage (approx.)
7 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x1 Massaranduba Decking
Species
Massaranduba
Nominal size
1x1
Actual dimensions
3/4" × 3/4"
Face coverage (approx.)
3/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x2 Massaranduba Decking
Species
Massaranduba
Nominal size
1x2
Actual dimensions
3/4" × 1 1/2"
Face coverage (approx.)
1 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x2 Massaranduba Shiplap Siding
Species
Massaranduba
Nominal size
1x2
Actual dimensions
3/4" × 1 1/2"
Face coverage (approx.)
1"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x2 Massaranduba Tongue & Groove Soffit
Species
Massaranduba
Nominal size
1x2
Actual dimensions
3/4" × 1 1/2"
Face coverage (approx.)
1 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x2 Massaranduba Railing
Species
Massaranduba
Nominal size
2x2
Actual dimensions
1 1/2" × 1 1/2"
Face coverage (approx.)
1 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Massaranduba Decking
Species
Massaranduba
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Massaranduba Pre-Grooved Decking
Species
Massaranduba
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Massaranduba Shiplap Soffit
Species
Massaranduba
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Massaranduba Tongue & Groove Soffit
Species
Massaranduba
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x3 Massaranduba Decking
Species
Massaranduba
Nominal size
2x3
Actual dimensions
1 1/2" × 2 1/2"
Face coverage (approx.)
2 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Massaranduba Bevel Siding
Species
Massaranduba
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Massaranduba Channel Siding
Species
Massaranduba
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
2 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Massaranduba Decking
Species
Massaranduba
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Massaranduba Nickel Gap Siding
Species
Massaranduba
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Massaranduba Pre-Grooved Decking
Species
Massaranduba
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Massaranduba Shiplap Siding
Species
Massaranduba
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Massaranduba Tongue & Groove Outdoor Flooring
Species
Massaranduba
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Massaranduba V-Groove Siding
Species
Massaranduba
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Massaranduba Bevel Siding
Species
Massaranduba
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Massaranduba Channel Siding
Species
Massaranduba
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
2 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Massaranduba Decking
Species
Massaranduba
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Massaranduba Nickel Gap Siding
Species
Massaranduba
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Massaranduba Pre-Grooved Decking
Species
Massaranduba
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Massaranduba Rainscreen Soffit
Species
Massaranduba
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
2 1/2"
Profile
Rainscreen
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
An overlapping lap joint engineered to shed water behind ventilated cladding systems.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Massaranduba Shiplap Soffit
Species
Massaranduba
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Massaranduba Tongue & Groove Soffit
Species
Massaranduba
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Massaranduba V-Groove Siding
Species
Massaranduba
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x4 Massaranduba Decking
Species
Massaranduba
Nominal size
2x4
Actual dimensions
1 1/2" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x4 Massaranduba Pre-Grooved Decking
Species
Massaranduba
Nominal size
2x4
Actual dimensions
1 1/2" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x4 Massaranduba Tongue & Groove Outdoor Flooring
Species
Massaranduba
Nominal size
2x4
Actual dimensions
1 1/2" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
4x4 Massaranduba Fencing
Species
Massaranduba
Nominal size
4x4
Actual dimensions
3 1/2" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Massaranduba Bevel Siding
Species
Massaranduba
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Massaranduba Channel Siding
Species
Massaranduba
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Massaranduba Decking
Species
Massaranduba
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Massaranduba Nickel Gap Siding
Species
Massaranduba
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Massaranduba Pre-Grooved Decking
Species
Massaranduba
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Massaranduba Rainscreen Siding
Species
Massaranduba
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Rainscreen
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
An overlapping lap joint engineered to shed water behind ventilated cladding systems.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Massaranduba Shiplap Siding
Species
Massaranduba
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Massaranduba Tongue & Groove Decking
Species
Massaranduba
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Massaranduba V-Groove Siding
Species
Massaranduba
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Massaranduba Bevel Siding
Species
Massaranduba
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Massaranduba Channel Siding
Species
Massaranduba
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Massaranduba Decking
Species
Massaranduba
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Massaranduba Nickel Gap Siding
Species
Massaranduba
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Massaranduba Pre-Grooved Decking
Species
Massaranduba
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Massaranduba Rainscreen Siding
Species
Massaranduba
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Rainscreen
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
An overlapping lap joint engineered to shed water behind ventilated cladding systems.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Massaranduba Shiplap Siding
Species
Massaranduba
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Massaranduba Tongue & Groove Decking
Species
Massaranduba
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Massaranduba V-Groove Siding
Species
Massaranduba
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x6 Massaranduba Decking
Species
Massaranduba
Nominal size
2x6
Actual dimensions
1 1/2" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x6 Massaranduba Pre-Grooved Decking
Species
Massaranduba
Nominal size
2x6
Actual dimensions
1 1/2" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x6 Massaranduba Tongue & Groove Outdoor Flooring
Species
Massaranduba
Nominal size
2x6
Actual dimensions
1 1/2" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x8 Massaranduba Siding
Species
Massaranduba
Nominal size
1x8
Actual dimensions
3/4" × 7 1/4"
Face coverage (approx.)
7 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x8 Massaranduba Siding
Species
Massaranduba
Nominal size
5/4x8
Actual dimensions
1" × 7 1/4"
Face coverage (approx.)
7 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x8 Massaranduba Timbers
Species
Massaranduba
Nominal size
2x8
Actual dimensions
1 1/2" × 7 1/4"
Face coverage (approx.)
7 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x1 Red Balau Decking
Species
Red Balau
Nominal size
1x1
Actual dimensions
3/4" × 3/4"
Face coverage (approx.)
3/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x2 Red Balau Decking
Species
Red Balau
Nominal size
1x2
Actual dimensions
3/4" × 1 1/2"
Face coverage (approx.)
1 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x2 Red Balau Shiplap Siding
Species
Red Balau
Nominal size
1x2
Actual dimensions
3/4" × 1 1/2"
Face coverage (approx.)
1"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x2 Red Balau Tongue & Groove Siding
Species
Red Balau
Nominal size
1x2
Actual dimensions
3/4" × 1 1/2"
Face coverage (approx.)
1 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x2 Red Balau Railing
Species
Red Balau
Nominal size
2x2
Actual dimensions
1 1/2" × 1 1/2"
Face coverage (approx.)
1 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Red Balau Decking
Species
Red Balau
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Red Balau Pre-Grooved Decking
Species
Red Balau
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Red Balau Shiplap Soffit
Species
Red Balau
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Red Balau Tongue & Groove Soffit
Species
Red Balau
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x3 Red Balau Decking
Species
Red Balau
Nominal size
2x3
Actual dimensions
1 1/2" × 2 1/2"
Face coverage (approx.)
2 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Red Balau Bevel Siding
Species
Red Balau
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Red Balau Channel Siding
Species
Red Balau
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
2 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Red Balau Decking
Species
Red Balau
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Red Balau Nickel Gap Siding
Species
Red Balau
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Red Balau Pre-Grooved Decking
Species
Red Balau
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Red Balau Shiplap Siding
Species
Red Balau
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Red Balau Tongue & Groove Outdoor Flooring
Species
Red Balau
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Red Balau V-Groove Siding
Species
Red Balau
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Red Balau Bevel Siding
Species
Red Balau
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Red Balau Channel Siding
Species
Red Balau
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
2 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Red Balau Decking
Species
Red Balau
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Red Balau Nickel Gap Siding
Species
Red Balau
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Red Balau Pre-Grooved Decking
Species
Red Balau
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Red Balau Rainscreen Soffit
Species
Red Balau
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
2 1/2"
Profile
Rainscreen
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
An overlapping lap joint engineered to shed water behind ventilated cladding systems.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Red Balau Shiplap Soffit
Species
Red Balau
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Red Balau Tongue & Groove Soffit
Species
Red Balau
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Red Balau V-Groove Siding
Species
Red Balau
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x4 Red Balau Decking
Species
Red Balau
Nominal size
2x4
Actual dimensions
1 1/2" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x4 Red Balau Pre-Grooved Decking
Species
Red Balau
Nominal size
2x4
Actual dimensions
1 1/2" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x4 Red Balau Tongue & Groove Outdoor Flooring
Species
Red Balau
Nominal size
2x4
Actual dimensions
1 1/2" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
4x4 Red Balau Fencing
Species
Red Balau
Nominal size
4x4
Actual dimensions
3 1/2" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Red Balau Bevel Siding
Species
Red Balau
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Red Balau Channel Siding
Species
Red Balau
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Red Balau Decking
Species
Red Balau
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Red Balau Nickel Gap Siding
Species
Red Balau
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Red Balau Pre-Grooved Decking
Species
Red Balau
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Red Balau Rainscreen Siding
Species
Red Balau
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Rainscreen
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
An overlapping lap joint engineered to shed water behind ventilated cladding systems.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Red Balau Shiplap Siding
Species
Red Balau
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Red Balau Tongue & Groove Decking
Species
Red Balau
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Red Balau V-Groove Siding
Species
Red Balau
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Red Balau Bevel Siding
Species
Red Balau
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Red Balau Channel Siding
Species
Red Balau
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Red Balau Decking
Species
Red Balau
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Red Balau Nickel Gap Siding
Species
Red Balau
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Red Balau Pre-Grooved Decking
Species
Red Balau
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Red Balau Rainscreen Siding
Species
Red Balau
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Rainscreen
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
An overlapping lap joint engineered to shed water behind ventilated cladding systems.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Red Balau Shiplap Siding
Species
Red Balau
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Red Balau Tongue & Groove Decking
Species
Red Balau
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Red Balau V-Groove Siding
Species
Red Balau
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x6 Red Balau Decking
Species
Red Balau
Nominal size
2x6
Actual dimensions
1 1/2" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x6 Red Balau Pre-Grooved Decking
Species
Red Balau
Nominal size
2x6
Actual dimensions
1 1/2" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x6 Red Balau Tongue & Groove Outdoor Flooring
Species
Red Balau
Nominal size
2x6
Actual dimensions
1 1/2" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x8 Red Balau Siding
Species
Red Balau
Nominal size
1x8
Actual dimensions
3/4" × 7 1/4"
Face coverage (approx.)
7 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x8 Red Balau Siding
Species
Red Balau
Nominal size
5/4x8
Actual dimensions
1" × 7 1/4"
Face coverage (approx.)
7 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x8 Red Balau Timbers
Species
Red Balau
Nominal size
2x8
Actual dimensions
1 1/2" × 7 1/4"
Face coverage (approx.)
7 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x1 Tigerwood Decking
Species
Tigerwood
Nominal size
1x1
Actual dimensions
3/4" × 3/4"
Face coverage (approx.)
3/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x2 Tigerwood Decking
Species
Tigerwood
Nominal size
1x2
Actual dimensions
3/4" × 1 1/2"
Face coverage (approx.)
1 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x2 Tigerwood Shiplap Siding
Species
Tigerwood
Nominal size
1x2
Actual dimensions
3/4" × 1 1/2"
Face coverage (approx.)
1"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x2 Tigerwood Tongue & Groove Soffit
Species
Tigerwood
Nominal size
1x2
Actual dimensions
3/4" × 1 1/2"
Face coverage (approx.)
1 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x2 Tigerwood Railing
Species
Tigerwood
Nominal size
2x2
Actual dimensions
1 1/2" × 1 1/2"
Face coverage (approx.)
1 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Tigerwood Decking
Species
Tigerwood
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Tigerwood Pre-Grooved Decking
Species
Tigerwood
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Tigerwood Shiplap Soffit
Species
Tigerwood
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x3 Tigerwood Tongue & Groove Soffit
Species
Tigerwood
Nominal size
1x3
Actual dimensions
3/4" × 2 1/2"
Face coverage (approx.)
2 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x3 Tigerwood Decking
Species
Tigerwood
Nominal size
2x3
Actual dimensions
1 1/2" × 2 1/2"
Face coverage (approx.)
2 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Tigerwood Bevel Siding
Species
Tigerwood
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Tigerwood Channel Siding
Species
Tigerwood
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
2 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Tigerwood Decking
Species
Tigerwood
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Tigerwood Nickel Gap Siding
Species
Tigerwood
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Tigerwood Pre-Grooved Decking
Species
Tigerwood
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Tigerwood Shiplap Siding
Species
Tigerwood
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Tigerwood Tongue & Groove Outdoor Flooring
Species
Tigerwood
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x4 Tigerwood V-Groove Siding
Species
Tigerwood
Nominal size
1x4
Actual dimensions
3/4" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Tigerwood Bevel Siding
Species
Tigerwood
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Tigerwood Channel Siding
Species
Tigerwood
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
2 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Tigerwood Decking
Species
Tigerwood
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Tigerwood Nickel Gap Siding
Species
Tigerwood
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Tigerwood Pre-Grooved Decking
Species
Tigerwood
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Tigerwood Rainscreen Soffit
Species
Tigerwood
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
2 1/2"
Profile
Rainscreen
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
An overlapping lap joint engineered to shed water behind ventilated cladding systems.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Tigerwood Shiplap Soffit
Species
Tigerwood
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Tigerwood Tongue & Groove Soffit
Species
Tigerwood
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x4 Tigerwood V-Groove Siding
Species
Tigerwood
Nominal size
5/4x4
Actual dimensions
1" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x4 Tigerwood Decking
Species
Tigerwood
Nominal size
2x4
Actual dimensions
1 1/2" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x4 Tigerwood Pre-Grooved Decking
Species
Tigerwood
Nominal size
2x4
Actual dimensions
1 1/2" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x4 Tigerwood Tongue & Groove Outdoor Flooring
Species
Tigerwood
Nominal size
2x4
Actual dimensions
1 1/2" × 3 1/2"
Face coverage (approx.)
3 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
4x4 Tigerwood Fencing
Species
Tigerwood
Nominal size
4x4
Actual dimensions
3 1/2" × 3 1/2"
Face coverage (approx.)
3 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Tigerwood Bevel Siding
Species
Tigerwood
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Tigerwood Channel Siding
Species
Tigerwood
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Tigerwood Decking
Species
Tigerwood
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Tigerwood Nickel Gap Siding
Species
Tigerwood
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Tigerwood Pre-Grooved Decking
Species
Tigerwood
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Tigerwood Rainscreen Siding
Species
Tigerwood
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Rainscreen
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
An overlapping lap joint engineered to shed water behind ventilated cladding systems.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Tigerwood Shiplap Siding
Species
Tigerwood
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Tigerwood Tongue & Groove Decking
Species
Tigerwood
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x6 Tigerwood V-Groove Siding
Species
Tigerwood
Nominal size
1x6
Actual dimensions
3/4" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Tigerwood Bevel Siding
Species
Tigerwood
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Profile
Bevel
Use face coverage for square-footage takeoffs. Varies with the overlap (exposure) you install to. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tapered clapboard wedge — thick butt edge to thin top edge — installed overlapping horizontally.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Tigerwood Channel Siding
Species
Tigerwood
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Channel
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A wide face rabbet forms a recessed channel between boards for a bold rustic shadow line.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Tigerwood Decking
Species
Tigerwood
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Tigerwood Nickel Gap Siding
Species
Tigerwood
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5"
Profile
Nickel Gap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Shiplap-style joints plus a face chamfer that leaves a consistent nickel-width reveal between installed boards.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Tigerwood Pre-Grooved Decking
Species
Tigerwood
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Tigerwood Rainscreen Siding
Species
Tigerwood
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
4 1/2"
Profile
Rainscreen
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
An overlapping lap joint engineered to shed water behind ventilated cladding systems.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Tigerwood Shiplap Siding
Species
Tigerwood
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5"
Profile
Shiplap
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Stepped rabbets on opposite edges let boards overlap, shedding water while allowing seasonal movement — a classic siding profile.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Tigerwood Tongue & Groove Decking
Species
Tigerwood
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x6 Tigerwood V-Groove Siding
Species
Tigerwood
Nominal size
5/4x6
Actual dimensions
1" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
V-Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
Tongue & groove with chamfered face corners, so every seam reads as a crisp V — popular for ceilings and accent walls.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x6 Tigerwood Decking
Species
Tigerwood
Nominal size
2x6
Actual dimensions
1 1/2" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x6 Tigerwood Pre-Grooved Decking
Species
Tigerwood
Nominal size
2x6
Actual dimensions
1 1/2" × 5 1/2"
Face coverage (approx.)
5 1/2"
Profile
Pre-Grooved
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A hidden-fastener groove is milled into the center of each side edge, so clips grip the board and the walking surface stays screw-free.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x6 Tigerwood Tongue & Groove Outdoor Flooring
Species
Tigerwood
Nominal size
2x6
Actual dimensions
1 1/2" × 5 1/2"
Face coverage (approx.)
5 1/8"
Profile
Tongue & Groove
Use face coverage for square-footage takeoffs. Part of the width sits inside the joint. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
A tongue on one edge locks into a groove on the other for a tight, flush surface — the choice for covered porches, ceilings, and soffits.
Loads on demand — drag to rotate, scroll or pinch to zoom
1x8 Tigerwood Siding
Species
Tigerwood
Nominal size
1x8
Actual dimensions
3/4" × 7 1/4"
Face coverage (approx.)
7 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
5/4x8 Tigerwood Siding
Species
Tigerwood
Nominal size
5/4x8
Actual dimensions
1" × 7 1/4"
Face coverage (approx.)
7 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
Loads on demand — drag to rotate, scroll or pinch to zoom
2x8 Tigerwood Timbers
Species
Tigerwood
Nominal size
2x8
Actual dimensions
1 1/2" × 7 1/4"
Face coverage (approx.)
7 1/4"
Profile
Eased-Edge
Use face coverage for square-footage takeoffs. Full milled width is exposed. Approximate — exact coverage varies with milling tolerance, moisture, hardware and gap spacing.
The standard decking profile: flat faces with all four long edges slightly eased (E4E) for a splinter-resistant arris. Face-screw or plug installations.
.png?width=180&quality=75&format=webp){kind=logo}